Hi all. I'm painting my series 1 and have found a paint code 26637. Painted the rear decker panel and it looks nice apart from when I put another panel next to it, the colour is a lot different. I've painted a bit of the rear pillar cover and hopefully I can put a photo on. Does anyone else have...
Hi all. I'm looking for the handbrake gaiter that goes underneath the tunnel. No luck on Ebay and Wins. waiting to hear from Wadhams, but not holding out much hope. Does anyone have one spare???? Cheers
Hi all. Just a quick one. Does anyone know the size of bolts that hold the hubs into the Carriers? I'd imagine they'll be 5/16" by 3/4" but would like to check. Cheers all.
Hi guys. I've got a 3.9 from a range rover to replace the 3.5. Has anyone else done this? The only problem I see is the water pump is too long with the viscous damper on, but i've heard my pump will fit. Does anyone have any tips? Many thanks
Hi all. Has anyone recoloured their seats with the woolies gear? I've got a set of good seats, but the colour is nearly out of them and back to bare. I'm wondering if the treatment would take to them. Many thanks.
Hi all. I'm getting ready to start a resto of my series 1 v8 and I'm wondering if anyone has converted the exhaust to a twin pipe set up? ie exiting from both sides. I was thinking about having them exit just in front of the back wheels so I don't have to route it round the battery box and fuel...
Hi all. I'm stumped. My usually reliable car is letting me down. I thought it had bad fuel in, so drained and put in good fuel. Cranked the new fuel through and it started but then cut out again. Tried next day and she flashed up straight away but died after 30 secs. Tried to wind it over but...
Hi guys. Does anyone happen to have a spare pair of front door cards in buckskin? I managed to rescue an interior from a car that was getting scrapped but the door cards have the quarter light opener in them. I'd need the earlier ones. I'm in Fife so P+P would be needed, which obviously I'd take...
Hi all. Does anyone have a part number for the Universal Joints for the drive shafts? Mine are both shot, but hopefully dingbro can supply. Cheers all.
Hi all. I'm needing a series 1 v8 fusebox as I've snapped mine in half while not paying attention fitting it. Can anyone help? Cheers all.
Edited By Beaser on 1206256795
Hi all. I was going to re-colour my sandalwood seats, but have instead decided to get them re-covered instead. My local upholsterer has got some nice vinyls, but not quite a perfect match. Does anyone know if you can still get the rover spec vinyls for the surrounds as well as the main parts...
Hi all. I'm thinking about swapping the 3.5 to a 3.9 or 4.6. I'm not wanting to go the fuel injection route because of the wiring implications, so I'm wondering, will the carbs fit back on? ( I know i'll have to up the jets) and can the distributor be fitted? Many thanks
Hi there. Does anyone know of a company who will recore my radiator, preferably in Scotland? If so, do you know if they manage to keep using the fittings for the fan shroud etc. Many thanks.
Hello all. I've just finished rebuilding my engine with it's SD1 heads and all new shiny bits. However the bloody thing won't start. I'm getting a spark but the plugs are still dry. There is fuel in the filter and in the float chambers. Could it be that there is not enough fuel in the tank? Also...
Has anyone bought pads and discs for a V8 recently? I've been looking at the prices from Wadhams, but I know that he has a habit of not telling you when the prices have changed. Many thanks.
Hi all. I'm getting the engine bay painted and would like to know the best paint to use. Do I use satin, or gloss with a matting agent? I'm told that satin stays quite soft and gloss is best, but what proportion of paint to matting agent do you recommend? Any help gratefull of course.
Hi all. I've just fitted my new heads and the rocker gear. When I bring the number 1 cylinder up to tdc on the firing stroke, there is little to no valve clearance. The heads have been skimmed so I'm wondering if I have to shim the rocker gear?
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.