Search results

Hi, My car (1976 2200 SC) has developed a few electrical faults. The heated rear windscreen doesn't work and I am keen to sort that. There was no fuse in the fuse box between 3-4 so started by putting a fuse in. This resulted in the heated rear window switch (rocker type) being illuminated all...

Hello, Last year I returned to Rover P6 ownership after selling my previous P6 a number of years ago. I had been on the lookout for another P6 for a while and had been to look at a couple of cars when in May last year I spotted what is now my car for sale. The car is a 1976 Rover 2200SC Manual...

Hi, http://www.gumtree.com/p/rover/rover-20 ... 1101565642 http://www.carandclassic.co.uk/car/C549813 I am keen to get back to P6 ownership and I have noticed this car for sale which is fairly close to me. It is difficult to get a good idea of condition from the pictures so think I will...

Hi, http://www.carandclassic.co.uk/car/C512568# I have noticed this car for sale which is fairly close to me. Don't have any details as yet, but not sure if the interior/exterior colour combination is original. It is difficult to get a good idea of condition from the pictures so not sure if it...

Hello, I am looking for a TC exhaust manifold, and sections to the middle box. Can anyone help with any of these parts? Thanks, Chris

Hi, I am sad to say I have come to the difficult decision that I should sell my beloved P6 as I am not using the car enough and access to a garage is beoming more and more difficult. I have a mini in mid restoration in my garage and my parents are getting fed up having the Rover in theirs!It is...

Hello, As the title suggests I'm looking for the stainless steel bonnet strip that sits over the headlights on the series 1 V8s if anyone has one to spare. Many thanks, Chris

Hello, I thought I would introduce my Rover 2000TC which I have had for two years. When I first got the car it had one month MOT and really needed a lot of work. I did the work needed for the MOT and enjoyed using it as a running restoration project - however I always knew it needed quite a bit...

Hello, I spotted this on eBay. Can anyone tell me if it is the correct gearbox for a 2000TC? http://www.ebay.co.uk/itm/Rover-4-speed ... 1c1e24422b Thanks, Chris

Hello, I am currently replacing the crankshaft in my 1970 2000TC. I finally got the engine out today and have begun the stripdown. It looks as if a new clutch will be needed shortly and I thought it would be best to do it now rather than later. Does anyone have a clutch for my car at a...

Hello, I have been reading a number of the valve related posings under this section and wondered if anyone could help me. I am looking for a few valve shims to get my 1970 2000TC on the road. Can anyone help or advise me where I could get some? I need sizes: 0.272 0.102 0.292 Alternatively...

Hello, I am looking for a few valve shims to get my 1970 2000TC on the road. Can anyone help? I need sizes: 0.272 0.102 0.292 Alternatively if anyone has combinations to give the overall sizes of: 0.374 0.374 Any help on this would be much appreciated. Harvey has been very helpful and...

Hello, Does anyone know where I would be able to get a selection of different valve clearance shims. This is the final job I need to do before I can get my 1971 2000tc up and running. Many Thanks, Chris

Hello, My name is Chris and I am from Edinburgh. I am 23 years old and have a 1971 Rover 2000TC in Zircon Blue. This car, although on a 1971 'J' plate, is in fact a Series 1 having been built in 1969/70 in Malta for it's original owner. I have had the car since November last year and so far...