Rover P6 4.6 V8 Road/Race car.

RoverAlex

Active Member
Hello. A few have recommended I sign up here and have a browse around for info so thought I would introduce my project.

For those that like a "pristine" Rover P6 this build might not be for you. And for those that would wince at the thought of the P6 being altered little, stop here :)

It was very early one Saturday morning just passed that Peter, a friend, and I were discussing the fact that there is an upcoming local club meet at Santapod the next weekend for the RYWB and neither of us currently have a car we can take as they were all off the road. This we both decided was unacceptable. After not much pondering we came to the conclusion that the Rover P6 would be a perfect drag/race/drift car and that we needed to get a 4.6 V8 by the end of the weekend.

So this is the beast. A Rover P6 3.5 V8 which has not been on the road since the 1980s. The body repairs were done before it was taken off the road. Peters friend kindly donated the car - so it seemed the right thing to make something out of it.

20140331_130231_zps947c7054.jpg


20140331_130221_zps021f5832.jpg


We were determined to find an engine that very weekend. After many phone calls we found one fairly close by (well..a four hour round trip) at a reasonable price - we wanted one with fairly low miles that had not been on LPG and of course it had to be the 4.6 V8 nothing else was considered. Late 90s Range Rovers are the best source for these it seems. Not wanting to waste time started stripping the engine while on the trailer.

Our target was to have the car ready to race in 5 days so with no time to slack, we were working in the evenings and I took time off work to attempt our goal. Not wanting to keep the EFI from the 4.6 that had to be swapped over for the carb setup from the 3.5. As did the front case, pulleys, water pump and so on. Thankfully this is a straightforward swap (the 4.6 being based on the 3.5 despite many years between them)

The 4.6 with all the modern gubbins on it:

http://img.photobucket.com/albums/v162/alex1981/Cars/Rover P6/20140331_210112_zps5c3f5686.jpg

And there we have it - the 4.6 with the manifold and carbs from the 3.5. These are 1.75" carbs which will strangle the engine top end, but they will do for now:

20140331_2209461_zps778b3c17.jpg


Then the front of the engine had to be swapped over. Not complicated really. Our only setback was that the timing gear and chain from the old engine was seriously worn out and we could not use the one from the old engine due to the design (apparently the gear from the Range Rover P38 was the only one different to every other Rover V8). So we ordered a fancy strong one and it arrived next day :)

20140402_175931_zpsd2fc52e9.jpg


New engine sat on the mounts :D Bolted straight up to the mounts and bellhousing (had to change the flywheel of course as the engine came out of an auto):

20140331_225317_zpsa092b13e.jpg


Because race car, interior had to come out. There's a good 60KG there.

20140402_085328_zpsb239e22a.jpg


20140401_212658_zpsc261de5f.jpg


Alternator bracket welded back together:

20140402_1405271_zps1cc958b3.jpg


Holley fuel pump and race cell installed with new lines etc:

http://img.photobucket.com/albums/v162/ ... 72789a.jpg

And it runs - see link to video below:

http://www.facebook.com/photo.php?v=101 ... .698935144

So after a little fettling on the morning of the RWYB day the engine was running very sweet. The first every road test was in order. With a quick whiz around the field we were happy and a little surprised that the brakes worked and it went forwards and backwards.

Upon arrival and a drive around the car park it was evident that the clutch was dead and we had no chance of getting any power down. But we had came this far - to give up now would not be sporting. So took it up the strip gently easing the throttle into what you could only call a gradual increase in speed rather than acceleration. Managed to get to 30MPH. But we can honestly say that we took a car destined for scrap to one with a beefy engine and a run on the drag strip in less than 5 days. Very happy with that.

DSC_9760-1280_zps36cefc10.jpg


DSC_9765-1280_zps9fdf38dc.jpg


We thought we might be able to make a modification to the clutch with a big 'ol screwdriver so we took the box out in the car park at Santapod. Nope, as expected clutch is dead and not a lot we can do. At least that is one job out of the way now the box is out.

Shortly after coming back from Santapod we bought this:

eatonSupercharger_zps0ff1dd16.jpg


It's an Eaton M112 Supercharger, originally from a Jag XKR 4.2 - in that car it produces 420BHP. Now of course our engine is much older and less efficient, it gives some idea that this is something decent. We were going to go down the route of 2" SU carbs and twin turbo. Problem is that the engine bay was pre-determined in a restrictive fashion as we know so there is not a lot of room in there - we could make it work but none of the options we particularly liked.
Details of the supercharger here: http://www.eaton.com/Eaton/ProductsServ ... PCT_221797

This will come much later on the build - for now it will run without a charger.

After much searching about in the back rooms of the local auto factors found some suitable silencers. Made up some mounting points. Sorted! Just needs some tailpipe trims to finish:

20140409_191516_resized_zps0437c784.jpg


20140409_191600_resized_zps15ba94a5.jpg


About two weeks into the build did a little more work for the autotest event we were entering that Sunday. Added cords for fire extinguisher and battery isolator:

IMG_2485.jpg


IMG_2486.jpg


Made some aluminium door cards. We wanted to keep the wood for a bit of character but cut down on weight a tad:

IMG_2483.jpg


IMG_2484.jpg


Sunday saw the Rover going to the autotest day with PMC at Rockingham. It was a first for me. I was fairly useless with getting the route correct but thankfully Peter was pretty good at pointing me in the right direction :)

The autotest found us a few leaks. Also found out that the oil pressure is zero on idle once the oil gets warm which is not great - uprated oil pump gears will solve that and need to sort the radiator. Nothing fell off or snapped which was a bonus. The amount of body roll is quite alarming (not that we held back) but that will be addressed shortly. We were told by bystanders that the tyres were flexing so much the metal of the rims came very close to scraping the ground :)

Sorted out the interior. Stripped it out including all the sound deadening - it took a lot of scraping, wire brushing, thinners and farting but we got there:

interiorstripped2_zps75f3f92d.jpg


interiorhalfpainted_zps73e3dd30.jpg


Door cards fitted and a quick go over with a scotch brite pad to give it a brushed look:

doorcardsbrushed_zpsb0ad6450.jpg


Corbeau bucket seats fitted. I think it's rather nice :)

1609816_10152068039677304_7444951739560377252_n_zps0744e1f6.jpg


Now towards the end of April 2014 did a taster session at Rockingham on the day that Retro Cars had a bit of a thing on. Was great fun giving it some beans round the track. Clearly we need to do some more work...it...well...as you can see from the pics leans a little! With the recently fitted Avo adjustable shocks turned up to also max that helped things a little. Brakes were pretty rubbish and didn't have much grip. But of course we will work on these things :)

A few pics from the day:

10250043_10152067999617304_5051102346099705024_n_zps828930b8.jpg


1980388_10201852021009239_6164917617524573002_o_zps7db44e17.jpg


1382782_245907042259283_626802183843105636_n_zps3c054d59.jpg


981273_245906982259289_6766860786716233475_o_zps5e0b5558.jpg
 
Still in April 2014 and loads of goodies arrived including this, an alloy rad from an Evo 1/2/3. It is only an ebay special but it will do a damn better job than a radiator with 3 rows missing, soldered up, and using bits of wood zip tied to the bottom in an attempt to stop it expanding :)

rad_zpscc049b15.jpg


As mentioned before we had oil pressure issues. We are running a 4.6V8 with the front cover etc (including oil pump) from the 3.5V8 we have mated to it - ending up with 0 PSI on idle and not much better running when warm. The front crankshaft oil seal was also leaking so that got replaced. To up the pressure to "normal" we got an uprated gear kit for the oil cooler. You get taller gears, a spacer, gaskets and shims to get the spacing correct. A very nicely made bit of kit:

oilpump_zps020ce905.jpg


And a Mocal oil cooler and Mocal sandwich plate to keep the oil temperate down a bit - it's a bit of a tight fit and we might have to take the water radiator out to do an oil change but oh well!

oilcooler_zps19eb9e75.jpg


Re-furbished the 2" SU carbs. Nice trumpets hey?

carbs_zps094cbdb4.jpg


Now running at 10PSI on idle and 30PSI running when running and warm - which seems about right for these V8 engines. Got the radiator installed and electric fan mounted but forgot to get a picture of those.

Beginning of May getting the suspension sorted out. It's not all guess work!

20140505_1245491024_zpsb8786aed.jpg


20140505_1245171024_zps156dcc46.jpg


Had some inspiration at Donnington from the Rover P6 race car. And that is to convert front and rear to 2.5" springs. This means it's much easier to change the springs to different lengths and poundage, as well as being cheaper than getting springs made to our requirements. Bought an adjustable coil over spring seat kit for the front. Then lobbed off the top of the old seats and mated the two. A spring seat was bolted (1" higher than centre for better spring location) to the bulkhead:

20140507_1836201024_zps2bfaf75d.jpg


20140507_2222531024_zpsdab4270c.jpg


Coil overs at the rear. Some old coil overs were butchered for the conversion. Standard 2.5" spring now sit over the Avo coilovers. Much lathing, cutting, grinding and welding later:

rearcoilovers_zpsb11cedfc.jpg


Hydraulic handbrake fitted (needs some work until it's effective):

Hydraulichandbrake_zps21ff1431.jpg


Sits about right I reckon:

20140507_2206171024_zpsdc2af9e0.jpg


11th of May 2014 went yesterday at Rockingham. What an improvement! Yes it still rolls as you will see from the picture but no where near as much - you can throw it around now without the worry that it might fall over! With decent rubber, rear brakes that work and poly bushes it will be better still. Had great fun :)

1499018_10201968755967540_804169261439692472_o_zps1e76ad81.jpg


As clearly shown in the picture above, we have quite a bit of blue smoke. Not ones to hang around as soon as we got back we stripped the engine apart. It'll need a bit of work, put it that way! Engine out and the rebuild starts. Wanted to finish it to a half decent standard so sprayed painted the block:

1enginemasked_zpsf44d34b4.jpg


Pretty hey?:

2enginepainted_zpsedb3657c.jpg


Gave the engine bay a spruce up too:

3enginebaytidied_zpsf696585b.jpg


Spent a little while sanding down the head with a sheet of glass and paper. Before:

4head_zps18c0ce3b.jpg


(the other side, but you get the idea) After. Good what you can do with a sheet of glass from an old picture. Decent surface I'd say:

5headsanded_zps1f4046be.jpg


A bit of head work:

6headsbeforeadafter_zps44594972.jpg


Brief mockup of the supercharger:

8superchargermockup2_zps2e40af57.jpg


New wheels arrived from America and got some Dunlop race tyres. Needless to say, a little work is required on the rear end so we had a go at rolling the arches and bashing bits with the big hammer. Some success. But this will not be so easy on the fibre glass wings we will fit. The tyres are pretty wide so used a baseball bat to roll the arches. Fairly easy on steel, not so simple when I fit fibreglass wings. (car sits high at the front as no engine in there) I think the front wings will only require a little trimming:

11wheels_zps5f602c42.jpg


12wheels2_zpsf6e981b8.jpg


Spent a lot of time with various different home-made rigs to balance engine components but decided to send them off for "professional" balancing. As luck would have it, we got them spot on so no work was required. Slight modification to improve oil flow:

20140808_2124471024_zpsae1fb774.jpg


I carried on with the valves and head. Course and then fine paste was used on exhaust valves, fine only required for inlet. It's crude using the drill to spin the valves but it does the job:

20140809_1045151024_zps69d8f0c8.jpg


Cleaned up various parts and painted - it would be rude not to compliment the shiny block.

20140809_1945251024_zps9acf6a54.jpg


20140809_1945341024_zps9207f42f.jpg


Crankshaft installed:

20140809_1956111024_zps761dc7d9.jpg


Now mid August, waiting for the Crowler camshaft and other top end bits to arrive spent a good part of the weekend on the Rover. Main target was to get the charger mounted on the adapted inlet manifold. So you take a stock Rover V8 manifold and left it to Peter to enlarge somewhat on the mill:

20140816_145916_zps1a49c368.jpg


Meanwhile I took way to long to cut strips of aluminium which Peter welds onto the manifold. Plenty of weld so we can smooth it out later:

20140816_185226_zps579dbefd.jpg


Welded up, ready for the top of these uprights to be milled to the correct length:

20140816_183942_zps8e793d2c.jpg


Plate cut and drilled:

20140816_192514_zps117a35d0.jpg


20140816_193328_zps1da473c3.jpg


Next trial fit:

20140817_131021_zps9991a133.jpg


Last thing that Sunday polished up the rocker covers a bit. They are not perfect but they are certainly less manky. Trial fitted and zip tied the 2X 2" SU carbs to the back of the charger to get an idea of what it will look like. Crude measurements show that it it may well fit into the engine bay with no modification to the bonnet:

20140817_201637_zpsd1f281ff.jpg


20140817_201753_zpsbbc5b10f.jpg


20140817_201700_zps03d667e6.jpg


Cut back the valve spring seats to accept the double valve springs (compare top and bottom head):

20140821_2030411024_zps48290f1a.jpg


And then cut the top of the stems by 2.5mm (due to the extra lift of the cam):

20140821_2053001024_zps24a18953.jpg


So there is how it stands at the moment. Current news is that I am going to take on the project instead of it being a joint venture and I am aiming to get it on the road. I need to find and LT77 bell housing to mate to an R380 box I have as I feel if I fit the standard box it will rip it apart in no time. Got a Jag rear end, jag front brakes but not sure which route I will be taking yet regards to those.
 
RoverAlex said:
Hello. A few have recommended I sign up here and have a browse around for info so thought I would introduce my project.

For those that like a "pristine" Rover P6 this build might not be for you. And for those that would wince at the thought of the P6 being altered little, stop here :)

I don't think there are many people like that one here. Most of our cars have been altered in some way or other and I've enjoyed reading about what you're doing.
 
Thank you for all the positive comments. As mentioned all the work so far has been done between me and a friend but now it's having some work at a garage before I get it back on my driveway in my sole possession where the rest of the work has been done. Glad to see that you lot are not adversed to modification...although mine are not exactly subtle. To give you an idea when I walked into the garage today to drop off a fan belt they were in the process of whacking the rear doors with a sledge hammer after cutting the inside arches out to make the tyres fit :D It's not just a slight trimming, either!

Today it's also had new pads all round, new brake lines (including adapted Goodrich flexies that I had left over from my Range Rover) and the engine is fitted. Hopefully it'll be on my drive on Friday and I can continue the work there. The plan now is to get an MOT on it so I can run in the 4.6.

You would have probably seen almost the same post on Retro Rides but I thought perhaps more people would be interested on this forum. I'll continue to post if there is interest.

Love it! And love the fact that you HAD to find a 4.6 in such short time - excellent! :mrgreen:

Quite correct, it *had* to be done :)
 
RoverAlex said:
You would have probably seen almost the same post on Retro Rides but I thought perhaps more people would be interested on this forum. I'll continue to post if there is interest.


Yes that's where I had been reading them, but as you say, there will be a better qualified audience on this forum.

Graeme
 
So it's now on my drive and is my sole project. The downside of that means no way of fabricating or doing major work. The upside is I can nip out and spend the odd hour here and there whenever I can.

So the engine is in. I need to get it road legal before I can really test it but it seems to run well. Revs up very freely like no other Rover V8 I have driven. Oil pressure seems very good, no apparent leaks or odd noises. So I'm happy with that.

20150327_175955_resized_zpsolizf3jg.jpg


Wings fitted and rear wings butchered to suit the tyres (substantial alteration to the inners required)

20150327_180037_resized_zpsetjb7zqe.jpg


DSC_1939-1280_zpsmrgdyqwc.jpg


Looking at this pic one of the lights clearly isn't right I'll have to look at that over the weekend.

20150327_180242_resized_1_zpsn1y5knav.jpg


Had a quick browse round the car - some of the electrics work but need to figure out the lights and other things, fit a hi/low beam stalk, rear view mirror, fit some arch extensions certainly at the rear, fuel pressure regulator, carb socks and things like that.
 
Been thinking about paint. I want to keep it green but it won't be Lunar Grey (green according to DVLA). I was thinking something along the lines of this:

Green_zps1xuyvyd2.jpg
 
Back
Top