Search results

Hard to get correct but they are out there . Have now converted my fuses to modern blade type and new box so no worries about melting. Etc

Fitted electric facet type with inline fuse and ignition switched feed . No regulator used and pushing from under tank to carbs. Not quite cured the dreaded vapour lock issues and I retained mech fuel pump at first but now just electric . Planning on drilling out return line restrictor next...

I recall when I had an escort mexico way back in 1972. that was fast in its day and could easily keep up with jags etc ( to 60 at least) and actually out turn ( handling was excellent) them on corners with late braking etc. recall rover 3500 as police cars and they were fast away...

hmm sign in car is an idea. next year will try and bring my old rover along with a bit of info .eg about car. owner etc might be interesting of we all did. hope the guy whom lost a core plug got home OK

went to Whietwebbs museum of transport today. entire group of rover owners as set up by rover sports club I believe. aside from having a few dozen rovers of all ages including modern ones ( not sure thats so good but aware its open to all rover owners including bicycles!) the museum...

I could supply my dizzy's numbers but as its a 3500 and not a 3.9L one would assume you need the numbers from a range rover where they used 3.9l lumps! if nobody comes up with data needed, maybe a check with range rover clubs?

sounds nice. hope weather is kind. i am too far away and cannot trust my p6 enough to go far as its not keen on traffic! ( working on that) my nearest trip this sunday will be to whitewebbs museum in Enfield this sunday being held by joint rover sports club. ( sadly taking my normal...

my thoughts but having stripped entire rear axle with diff off and checked on a bench .unable to find anything amiss or sticking/not working. probably missing something silly . I was considering stripping down again in summer and checking the actuating pins and pistons are ok. though whats...

noticed my brake fluid going down .no leaks found ..topped up.. brakes sticking on .. so removed servo for exchanging ( wins) and lo and behold ..servo full of fluid! I replaced brake master cylinder too. footbrake needs a touch more pressure than last servo..funny that! but handbrake...

nice to be made aware the scoops actually have a function and not just for show. personal taste would put me off those though as looks like the sort of thing kids? would do to soup up or make his car look 'cool'. still everybody has own ideas of taste. much like fitting spoilers on...

looks worrying like a world of stripping back with lots of welding and rebuilding. not for the squeamish but given enough time and effort is do-able.

much ado about gas flow and porting. when I was young and had an escort mexico Mk1 ( 16oogt kent lump) I thought about that and got advise that as long as outer gasket and exhaust flange was slightly larger than exhaust and inlet ports then gas flow would be good. any further...

hmm. I always get a mid range heart attack when cornering above 35mph in my rover. agree t holds road but the degree of roll is heart stopping! so if? theres a reasonably priced into roll bar we can buy? its probably going to sell but depending on number of owners needing/wanting and...

i have about 2" of play in steering wheel but it does not wander . that is more often caused by excess play in joints .out of line steering geometry etc . cannot comment on amount of play that ought to be correct ( as from new?)

ether can assist starting but the oil / diesel mix in bores will greatly assist doing damage to bores when engine has not bene cranked for some time. a few choice words is always helpful but if its anything like my car..it will turn a deaf ear anyway. good luck.

before turning crank with large wrench etc pull plugs and inject a couple of teaspoons engine oil and mixed with a little diesel . allow 10 miss standing for ring to soak then try slow turning by hand. its teh rings that tend to stick to cyl walls and if we can ease the...

good point clive and for that reason I changed my entire exhaust system . still not as quick as it ought to be but never found why ! before fitting electronic dizzy ( complete unit with incorporated advance module) it did now again act suddenly like a turbo had kicked in and gave a...

lots of good advise . fuel starvation and incorrect timing have big effects on performance. assuming we have checked other factors as mentioned then we need to simply go through all possibilities. does sound strange it won't pull uphill. when that occurred to me I found front brakes...

if I had my engine stripped enough to have lifters out..I would replace with cam and chain etc all at same time. though admittley it will removes most varnish and carbon . a lot of work!

hmm my search revealed no helpful results. have we thought about contacting Mahle ? whom now own Vandevell. they will have data and may? respond to a polite email. other ideas if nobody can respond would be sites such as petrol heads. can we add other info? are they boxed? new? did...

easy if we have a sticking piston in a caliper? as you have replaced these and new hoses ..we ideally need a brake testing as used for MOT's thus each wheel can be checked . just in case its a rear brake causing this or..worn joint (s) rubbers. if we have say a steering ball joint...

aware of that case. yes was a sigh of the times when very poor quality control mixed with workshy and troublesome issues from workforce and out of date management attitude to its workforce etc all combined to kill off UK motor industry virtually. having worked for a vehicle...

if studs look OK? then we are better of sacrificing housing. these are far easier to replace than a stud that may be corroded into position. the crud/corrosion that occurs from dissimilar metals will cause adhesion to stud/housing and likely also eat into both! so we get a weaker stud ...

damn .missed those. envy now but well done.

good luck with your project . it involves endless hours of labour .deep pockets . mountain of patience and a few choice words from time to time . the inboard rear brakes being well recognised as a source of bafflement and annoyance to many an owner. ( self included) comment noted on the...