Search results

  1. P

    Central gear stick console.

    No problem Mr task I'll dig it out and e mail you some pics just to make sure it's what you need
  2. P

    Central gear stick console.

    Hi Dean I believe I have a centre console for a manual V8 if you are still after one
  3. P

    Composite gaskets

    Thanks for the advice Peter illI probably go with the standard tin gaskets for now never knew about the pre load for the liftersl either so Will be looking that up as well thanks once again
  4. P

    Composite gaskets

    Evening All, I recently bought an engine rebuild kit for my late r reg v8 p6 the kit was described as being for the 3.5 engine with the 9.35 compression ratio which mine is ,however the kit contains composite head and valley gaskets which I have been informed may not be suitable for the p6.Any...
  5. P

    O/S/R Wing

    Hi neil I have a rear wing but not in Corsica blue alas
  6. P

    Rover 2200

    Hi phil I will check the sound deadening and get back to you
  7. P

    Rover 2200

    Hi badrover if I remember correctly the engine would not idle of its own accord but the gearbox was fine
  8. P

    Black ambla drivers seat

    Hi clive, I know itsi a bit late but is the drivers seat up for grabs
  9. P

    Rover 2200

    Hi Clive, the curved part is in good condition but alas I believe the colour is buckskin
  10. P

    Rover 2200

    Hi Alex, the seats and the passenger shin bin have already gone if that is what you were after Regards Paul
  11. P

    1977 3.5 litre P6 soon to be available

    Hi there I am interested could you pm me a contact number so I can have a chat with you Regards Paul
  12. P

    Rover 2200

    Hi everyone, I will be going to break a 2200 automatic with single carburettor in the near future so if you have any parts you need please let me know
  13. P

    For sale a set of Buckskin leather seats.

    Hello there can you pm me a contact number so I can give you a call regarding the seats
  14. P

    Series 2 doors

    Hi everyone, bit of a long shot but I'm after a set of doors for my j reg 2000 SC and I'm after them in the colour almond, this is just to save all the hassle of getting them resprayed etc.
  15. P

    parts catalogue and a few other bits

    Hi Jamie would be interested in the part's catalogues and the p6 news if they are still available Regards Paul
  16. P

    Jacking points

    Thanks Vern even better
  17. P

    Jacking points

    Oh well wood it is then and I'll be cutting the front end away as it's going to be scrapped
  18. P

    Jacking points

    Hi Colin thanks for that, I will do as you have suggested but I think I will try and get hold of a piece of box section steel rather than the wood as I don't trust the wood, i have visions of it snapping while I'm underneath Regards Paul
  19. P

    Jacking points

    Hello everyone I recently purchased a scrapper as a donor car for my 2000 SC and I would like to get it jacked up high enough to remove the engine/ box ,rear axle and front suspension etc so I would like to know where the best place to put the 4 axle stands on the body itself.a my ideas very welcome
  20. P

    Later gauges

    Hi all thanks for the replies I'm glad there's some light at the end of the tunnel, firstly i have a donor car albeit a different model so getting everything required shouldn't be a problem as long as the dash loom unplugs somewhere and I don't have to remove the whole car loom and secondly...
  21. P

    Later gauges

    Hi everyone I am currently running a 1970 2000 SC which has the oblong speedo and associated gauges, however I have the chance of a set of later gauges from a 74 2200 Tc with the round speedo etc which I prefer the look of and I was wondering if I could swap them over, any advice would be...
  22. P

    New member says hello

    No problem as soon as I find my feet around the site I will post some pictures
  23. P

    New member says hello

    Hi everyone and thanks for letting me join forum I'm new to the p6 scene but quite familiar with Rovers having owned several p5bs anyway I am now the proud owner of a 1970 2000 SC which is moted and running but does need work but hopefully I am in the right place for advice etc
Back
Top