Search results

  1. cobraboy

    Finally a tidy 3500S!

    :)
  2. cobraboy

    Finally a tidy 3500S!

    OK H I guess that means I am just about OK. I'm pleased as Tesco's only have vegan humble pies and I don't much fancy one of those.
  3. cobraboy

    Finally a tidy 3500S!

    Of course if you happen to have a bearing puller collar that you can bolt up around the thrust collar and access to a 50 ton press, or again one of those fancy hydraulic pullers that work with a puller collar then yippee, no problem, I'll retract what I said and order a large humble pie.
  4. cobraboy

    Yellow headlights on my P6, would it work ?

    Wilfred The lights look very calming and soothing, nice work.
  5. cobraboy

    Finally a tidy 3500S!

    Yeah OK Someone will now say.... huh, my grandad pulled hundreds of those off back in the day... Well good luck trying.
  6. cobraboy

    Finally a tidy 3500S!

    Thems won't pull off sir !
  7. cobraboy

    Finally a tidy 3500S!

    I referred to it as a spacer as you called it so, I thought it easier to use that name than call it a thrust collar, then you would have maybe queried if it was indeed the same part. So here we go - replace the thrust collar as you have to cut the original to get it off.
  8. cobraboy

    Finally a tidy 3500S!

    Yes To change the seals new spacers are needed.
  9. cobraboy

    P6 jack

    Jack in good condition. £40.00 PLUS SHIPPING ****SOLD****
  10. cobraboy

    PAIR FRONT SPRING CUPS

    As title, good condition. £20.00 PLUS SHIPPING ****SOLD****
  11. cobraboy

    BELL CRANK ASSEMBLIES

    For sale nice clean pair of front bell cranks. Good un pitted bearing surfaces. Complete with bulk head mountings that are the stud type. £40.00 PLUS SHIPPING ( Heavy !! ) ****SOLD****
  12. cobraboy

    Crank bearings

    Be sure to check both sets for sizing, ie, STD or + 0.??"
  13. cobraboy

    Differential removal - is workshop manual correct ?

    Be sure to take careful note of all the spacer and washer locations on the long bolt at the front of the diff extension, nose height is critical to avoid vibration. Also whilst diff is out check all driveshaft UJs for smooth operation in all directions.
  14. cobraboy

    Getting back on the road

    Us skinny runts don't slide around that much, I wonder if it is the seats fault, or the reason for the slippage is the fact that the driver is not as 'sporty' as he could be ? Not casting Nasturtiums, just throwing it out there ;) PS I personally thought you were cutting a fine figure when I...
  15. cobraboy

    Solex carburettor spewing fuel - help!

    Try here for help https://classiccarbs.co.uk/products/other-carburettor-parts/solex-carbs-parts/solex-parts/ https://www.carburettorspecialists.com/products.htm
  16. cobraboy

    My '72 P6 V8 is back in use on UK roads and once again wearing its silver on black 'K' plates!

    Sure. The breeding programme has been unsuccessful so one might as well go.
  17. cobraboy

    My '72 P6 V8 is back in use on UK roads and once again wearing its silver on black 'K' plates!

    I have both V8 and strong 2200 diffs here, might keep you going for a couple of months :LOL: Both in nice condition, also have spare pinion extension shaft in case you get bored with breaking output shafts .........
  18. cobraboy

    My '72 P6 V8 is back in use on UK roads and once again wearing its silver on black 'K' plates!

    You might ask him to fit new oil seals to both sides and the pinion extension whilst he has it on the bench.
  19. cobraboy

    SU HS6 CARBS FOR SALE

    Pair of 1 3/4" HS6 carbs, ex P6 in nice, as removed order. £150.00 + SHIPPING Edit These carbs did not come off the engine I have for sale, although they could go with it, although I do not have an intake.
  20. cobraboy

    3.5 LITRE V8 ENGINE FOR SALE

    Came out of my P6. 10.5:1 CR. Was running when removed, a little smokey so will need refreshing. Has done 87k. No carbs/ intake. Has distributor. Collection from North Suffolk. £200.00
  21. cobraboy

    Neatening the boot lining

    Dead posh that, 10/10
  22. cobraboy

    Oil pressure

    My 3.9 engine has a remote oil filter mounted fairly high up on the inner wing, also an oil cooler mounted lower down in the nose. There is a problem getting oil pressure up on start up. Firstly I just crank the engine until the oil pressure light goes out ( it won't start without me adding...
  23. cobraboy

    LEAKY DIFF ???

    The thrust collar should be a very tight fit on the output shaft. The WM calls for a press, I used a press, I would not have said so otherwise. Nit picking on someone elses for sale thread when you have no intention of purchasing the item is bad form.
  24. cobraboy

    LEAKY DIFF ???

    Depressed to find oil running down over your rear brakes ? Fear not here, for sale, is a pair of diff output shafts fitted with new seals and bearing spacers - ready to fit ! It’s quite a faff to sort out leaky output shafts and most folks don’t have the tools do the job, a press is needed to...
Back
Top