Search results

I just wind down the window and listen to the V8 engine through the stainless steel exhaust pipe nothing better.

Hello all does anyone know who would be a point of contact for the Berkeley Castle Show on 19 June.

Hi Pilkie I have finally put my car back together and I am going to Berkley Castle I already have my pass. Would there be any chance of parking with the other Rovers on the P6 stand regards Gary.

Hi Pilkie/Harvey I think that you will have the answer to the final part of my question and I am hoping that Harvey will read it and send some helpful advice as well. I have a Rover 3500 Auto J reg 1970 I purchased the car off a gentleman after his father had passed away. Before his father...

Hi Pilkie Some time ago you kindly sent me a panel fitting order to refit the panels back on my Rover after they have been painted. Can you remind me of that order as I am now at that stage for them to be refitted after there re spray. Are you going to Berkley Castle this year again it will be...

Great thank you will have it sorted by the weekend I am sure. Regards Gary CFH1J

Hello Demetris Many thanks for your reply, do you know I looked long and hard to find out how to get the handbrake set up to how it should be and I could not find it any where. I all the manuals I looked at all it says is how to put it back together again. When you say about the Factory Manual...

Hi Harvey many thanks for your information by looking at the way you have said to do it I take it that is the proper way it should be done and again I thank you for that. Have you by any chance done it the way Mike is saying and do you get the same result ie is it good enough to pass the MOT...

Hi Mike thanks for your advice I am at that giving up stage now after trying to work it out but your way does sound much easier to adjust it up using the booster to do the work, and it will spur me on to get the brakes bleed so I can use the foot brake to correct the hand brake problem. Thank...

Hello all Can any body help with some advice about my hand brake problem that I am having with my 3500. I have put the car back together after having the rear callipers over hauled with new seals and having new brake discs and pads. While I was doing this I have replaced all the rear bushes...

Hello Can anybody please tell me what is the correct Gearbox oil level to fill upto on my Rover P6 3500 (1970) when it is cold there are 2 cut out marks on the Dip Stick which one do I fill up to. Kind Regards Gary CFH1J

Thanks Pilkie Smearing the inner tube in grease sounds much better. Will do thanks for your advice. Hope to see you at Berkley Castle in 2016. Kind regards Gary CFH 1 J

Colin Many thanks for the information will do after replacing the oil seal. kind regards Gary. CFH 1 J

Hello everybody hope you are all well. Can anybody please tell me how much oil and what type to put in the Di-Dion tube. Or is it like any other amount where you just fill the tube until it runs out of the Brass filler plug but to me that would seem rather a lot of oil. Can anybody please...

Many thanks I thought that there was some order that they had to go back on the Car but just a simple understanding of how the car was put together in the first place. I must admit I have already fallen into the trap of removing the door hinges, that will be fun to get them back together...

Hello everyone Can any of you wonderful people out there help me. Does any body have the fitting order for re fitting the Body Panels back on to the Rover P6 after removing them. Thank you. kind regards. Gary. CFH1J

Hello Phil Many thanks I have just spoken to Mark. Regards Gary CFH 1 J

Hello all Can anybody help I am trying to locate a replacement Oil Pressure sender that shows the oil Pressure on the gauge and not the light. I understand that Britpart do offer a replacement but I need the Part Number so I can order a new one does anybody have such a number, or can anybody...

I purchased these number plates from an well known internet site. Can I please as members and all who view them are they the correct spacing or have I wasted my money. Or is it just me because there is only one number in the plate and it don't look correct ?

Engine done rest of the car to do.

Hello Can any body please give me some advice. I have replaced all new seals in my brakes (Calipers) on my P6 3500 and a new Master cylinder. What would be the best type of Brake Fluid to use. Regards Gary.

Hi John yeh the good old peg trick well after all its been there for 15 years so I guess it must work.

I have now worked out how to use my Phone to take some Pictures let's just hope they come out so you can see them. CFH 1 J is a P6 with 67k on the clocks she looks ok after being locked in an unused garage for 15 years. A few problems with her apart from being partially ceased she bent o Push...

Hi all just to bring you up to date the P6 that had been in the garage for 15 has a stuck valve. On start up you could hear that all was not right and as a result the push rod was bent and the Valve in the picture is stuck open. I can not move it any way I have tried everything to no joy. I...

The Story so far on the find of CFH 1 J ROVER P6B 3500 Automatic Registration Number CFH 1 J This is a brief history about Registration Number CFH 1J Rover 3500. In early September of 2013 my Wife and I were looking for a new home to rent in Gloucestershire. We had made arrangements to view a...