Search results

Hi Folks Has Tony Buntings E-mail ben hacked ? As I am getting the occasional E-mail from him ,that has a suspisious link Best Regards Adam

Good Day folks My fuel sender has developed a leak from one of the joints . How easy is it to resolder the joint ? and do I need any special tools ? Or will a soldering do the job ? Many Thanks Adam

Hi Folks Does anyone know how to remove the button from the side of ET headrests ? Do they just pull off ? Thanks Adam

Hi I am after some of the waist finishers that go at the end of the door window frames ,part numbers 364542/364541 & 364529/364530 ,I have had a good search ,but no one seems to make them. Thanks ,Adam

This is an odd one ,but I will describe what my car is doing When I pull away ,it feels like the car is hesitant ,but once it is up to speed it is fine ,but below 30 it seems intermittent,almost like the power is coming on and off ,it feels like it is something to do with the propshaft . If I...

I have read somewhere that the top ball joint is adjustable ,is this the case ? Many thanks Adam

Hi All I have started to fit the new carpet set ,but I am having difficulty getting the sill pieces to fit nicely has any one else had this problem ?

Hi all ,I have recently bought a new carpet set ,and I was wondering what the best adhesive was . What have you all been using ?

Hi Does anyone know the size of the fuel pipe union on the top of the reserve tap ? I am after the 90 degree one which connects to the nylon fuel hose ,also does anyone know where I can get one . Thanks Adam

Hi Folks My reserve tap has a leak ,is it possible to bypass it ? as I never use it ,plus I have read that doing the o-ring is a bit of a mare on a V8 ! cheers Adam

Hi all Can someone tell me where I could get hold of the terminal post that is located on the drivers footwell floor ? the one I have is badly corroded ,there appears to be a similar product for land rovers /Range Rovers ,the part no I am after is 565829 cheers Adam

Hi I am after two front door skins ,as my front doors are shot ,and full of filler ,can anyone help ? cheers Adam

Hi all Does anyone know where I can get 2 of the above ? I know Wadhams does half door skins ,but I would prefer the full skins for both front doors . cheers Adam

Hi Has anyone got any of the above they would like to part with (for a reasonable sum of course) Preferably in the Herts,Essex ,Cambs area . Cheers Adam

Hi Folks I have a strange problem with my main beem ,if I turn the main beam on ,it will only operate on the outer headlights ,however if I operate the flasher ,only the two centre lamps flash ,I have checked the fuses ,and had the main beam/dip switch off and cleaned it ,but I am not sure if...

Hi Folks I have an odd request ,I have been asked at work to try and source a master cylinder ,on the drawing it looks like a clutch master cylinder similar to the one on a V8 P6 but the dimensions are slightly larger ,the distance between the two mounting holes needs to be 2.5 inches ,the P6...

Hi all I have an odd request ,does anyone know the distance between the two mounting holes on the V8 master cylinder ? I have a job at work and a component looks similar to the master cylinder ,and also what is the piston bore diameter ? Cheers Adam

Huzzah ,another MOT Pass ,with a couple of advisories ,but different ones from last year :roll: :lol: still I aint complaining :D

H all :) Can anyone help ,I am after something to fill the hole for the gear lever in the base unit gearbox tunnel ,at the moment there is just a big hole ,the car was originally an auto ,but has had a 5-speed manual conversion ,does anyone have any suggestions ? cheers Adam

Hi all I am planning to do an oil change ,as I have a sticky tappet ,someone recommended I should use an engine flush ,but I have read that these are no good for an older engine ,I have read that putting some dexron 2 atf is a possible cure for a noisy tappet ,is this the case ? Cheers Adam

Hi I am about to fit a new clutch master cylinder ,as that has packed up too :roll: Has anyone got any tips or hints to make fitting easier ? (apart from removing the engine :lol: ) The old one came off no worries ,but I am guessing fitting the new one could be a bit fiddly :!: cheers Adam

Hi ,can anyone help On my 3500S ,which has an LT77 5 speed conversion I have to push the clutch pedal all the way to the floor to operate the clutch ,and the clutch bites as soon as I release the pedal ,I am also losing a bit of clutch/brake fluid ,but sometimes the pedal will operate normally...

Hi All :) This is an odd one ,I have recently fitted a refurbed wiper motor ,as the old one siezed solid :shock: but when the new one is operated the wipers do not park properly ,and do not operate correctly ,it is almost as if the motor is for a left hand drive car ,I think that if I could...

Hi All Is there a way of testing the wiper switch ? as I think mine has burnt out ,it was working OK on all settings ,except 2 where it would work intermittant ,and then it just stopped and blew the fuse ,also the amp meter dropped down to zero ,and now it will not work at all . Cheers Adam

To make sure the petrol flap is fully shut ,that way you won't get the strong smell of petrol every time you go round a roundabout ,and then convince yourself that the fuel system is about to burst into flames :roll: :oops: :lol: Jeez wot a doughnut :roll: :oops: