Search results

  1. K

    Fuel leaking from carburettor vent

    English please?
  2. K

    Fitting power steering to 2000TC

    Yes it is this bold I did mention, what wrench is needed? Because I have metric here and it is inches from that time. In mine case a mix by the way, maynbe because the rover is build in belgium. I did see your picture shows a exgra bold just next to the mention bold, t his is not the case in...
  3. K

    Fitting power steering to 2000TC

    The rust is because the privious owner has let go all ythe break oil and steerbox oil who is corrosive. But the rust looks much more heavy then in reality, it is just a thin layer.
  4. K

    Fitting power steering to 2000TC

    It is one of the three bolds the steeringbox is fitted with to the chassis, the one who make trouble is the one on the wheel side, it has no split pin, so it are not the ball joints.
  5. K

    Fitting power steering to 2000TC

    I have also a question, one bold used to fot the box on the car chassis I can not loose, it is the special version on the outer side, not the long bolds but the short pass bold, also I do not now the wrench valeu to loss this bold. it is quite difficult. regards
  6. K

    Fitting power steering to 2000TC

    Oke That does make sense. Mine citroen saxo does stop the motor when I do not steer, for example on a highway. Only when go steering it helps. I think for a pressure sensor there is a need to stay on pressure, so there is also a kind of valve who keep care of that, but also the steer box...
  7. K

    Fitting power steering to 2000TC

    You need a pump who do not always is on, there is a sensor for as you drive straight ahead, it is to prevent worn out motor. The sensor is on the steerings wheel, and sees where it is.
  8. K

    Rover P6 renewing project after 42 years barn live.

    Red for danger. The ignition works after program the right chip.
  9. K

    Electronic ign ition for the P6.

    Have build the ignoition who used a pic controller, so I can adjust the dwell electronically. Waithing for the case and then it go work for me. The circuit has a test setup with a jumper and can simple reconnected when fail, it work with points but also with a eye or magnetic pickup. On movie...
  10. K

    Rover P6 renewing project after 42 years barn live.

    Maybe re4place it by a electrical fan is better, I did read the cooling is not that good for the 3500 cars.
  11. K

    Rover P6 renewing project after 42 years barn live.

    I had a yellow color who was wear out completely so I did repaint it the same color. The fan do not miss any blade, it is asymmetric. I have now ready the pic controlled ignition module. just need a pic 16F88 to program it ordered but stores are closed.
  12. K

    Rover P6 renewing project after 42 years barn live.

    I have a manual steering box here, but I think these is from a 2200 or 2000TC mine rover is also right steered. The power steer is not badly damaged, just a part is damaged outside where steer column is connected. But thanks for the offer.
  13. K

    Fitting power steering to 2000TC

    I get a warning of dangerous site on that link.
  14. K

    Rover P6 renewing project after 42 years barn live.

    Did paint the fan, in nice new yellow.
  15. K

    Rover P6 renewing project after 42 years barn live.

    For the steering box I have the idea that this is bad, or bold was loosed and miss some metal after long use, it is cut away. the rest is complete.
  16. K

    Rover P6 renewing project after 42 years barn live.

    People like pics here so here these are. do not forget to answer the previous question about the steer box, this one will not remove it is quite stuck. I have now also done, the electronic voltage regulator, did draw original and made it modern with a mosfet. I have made a new circuit myself...
  17. K

    Rover P6 renewing project after 42 years barn live.

    Do somebody now what bold sizes are in the steer box attached to the car?. I did measure it but there are much inch values close by. Two I have removed but one who sits on wheel side and in a bus do not, the bold has inch size but I can not find what tool I need. Thanks.
  18. K

    Rover P6 renewing project after 42 years barn live.

    I have done now the wiper motor where connectors where broken by rust. Have set in brass contacts, and now it work fine again, however the over female connector is also damaged, the pins are rusted and stuck. So need work here or replacement, but think these connector pin can be replaced. By...
  19. K

    Rover P6 renewing project after 42 years barn live.

    In dutch please ;-) So now I do not now what white color I have, I do not now how many white color there are made.
  20. K

    Rover P6 renewing project after 42 years barn live.

    I have start the car with sparkplugs removed and some oil there. The oil pressure do rise to middle 30 and when stop, it slowly drops back, this last almost 5 minutes or so. Starter motor is not oke, it just clicks and sometimes starter go work, so start relais is damaged or contacts are dirty...
  21. K

    Rover P6 renewing project after 42 years barn live.

    Now I have remove the ignition stuff and clean it, the advance pot is leak, so I go restore it. quite easy with this rubber. bore out the ring holding rubber in pin, and tap thread in it for a 3mm bold. Did go fine. https://www.ebay.com/itm/335059885053 did use 1mm think rubber. it is...
  22. K

    Rover P6 renewing project after 42 years barn live.

    Ohh but I did, have derust the thing and spray paint it, all the flaps have new foam. I did disassemble it totally and inspect the heater radiator for leaks. pressuring it. and did the break booster also who was rusted.
  23. K

    Rover P6 renewing project after 42 years barn live.

    Hi Thanks. so on eye the oil is oke, not very old, maybe it is changed so I did ask previous owner. The motor is tryed to get started there, and without success seems. Compression is oke, and quite high!!! Need to go to lpg otherwise pingling occur. How much oil need in the engine including...
  24. K

    Rover P6 renewing project after 42 years barn live.

    Oke some new, I have open the carburetors to see what is inside. the pistons where stuck. I have remove them to clean, but want to let see what garbage it has on the surface do someone now where this come from? burned valve is not possible because compression is oke, tested by previous owner...
  25. K

    Rust proofing a P6!

    Some new people do read this and revive it automatically. Like me.
Back
Top