Search results

  1. J

    SD1 Engine rebuild

    ok thanks
  2. J

    SD1 Engine rebuild

    Hi all ,i,m looking to rebuild my 3500 engine ,any suggestions where to get parts, pistons ,cam shells ,mains etc, i was thinking rimmer bros or real steel ,what are yours thoughts please John.
  3. J

    KICKDOWN CABLE ADJUSTMENT

    ok thanks been trying today to set band but cant get anything to fit, so i,ll have a play tomorrow thanks
  4. J

    KICKDOWN CABLE ADJUSTMENT

    Harvey can you tell me what size socket is needed to set the adjuster on rear band please,
  5. J

    KICKDOWN CABLE ADJUSTMENT

    Ok thanks can you recommend where to buy a new o ring and filter please
  6. J

    KICKDOWN CABLE ADJUSTMENT

    Meant to say I have reset the adjuster
  7. J

    KICKDOWN CABLE ADJUSTMENT

    Now I have the servo off can I check rear band and what am I looking for. I have set the adjustment .
  8. J

    KICKDOWN CABLE ADJUSTMENT

    Hi Harvey, did.nt get to test drive today, as I had the sump off i checked the filter which was quite dirty also to my horror there was part of a rubber seal in there, so took of rear servo and part of the seal was missing AGAIN ,As you know this had recently been replaced what i thought was a...
  9. J

    KICKDOWN CABLE ADJUSTMENT

    Ok thanks going to check level again ,is after selecting all gears as you would on a cold check ,then i,ll go for test drive.
  10. J

    KICKDOWN CABLE ADJUSTMENT

    OK Harvey, thanks also , i have a remote cooler which is about 7 x 12 inches which seems big to me ,what do you think
  11. J

    KICKDOWN CABLE ADJUSTMENT

    Hi me again, i have altered the throttle linkage so now i have full travel on cable, do you know where roughly oil level should be in box, as i dont know if i have correct length , dip stick as mine is short ,it comes inside the car, as this is in a ford pop hotrod Please
  12. J

    KICKDOWN CABLE ADJUSTMENT

    Ok thanks very much for your help. I need to modify my linkage to get more lift.
  13. J

    KICKDOWN CABLE ADJUSTMENT

    I have taken up slack in cable ,now i need to modify linkage to get more lift on cable.
  14. J

    KICKDOWN CABLE ADJUSTMENT

    this is at rest
  15. J

    KICKDOWN CABLE ADJUSTMENT

    Thanks very much for your help ,my kickdown cable is a 16 inch, please can you tell me what cam i have from picture ,this is at full throttle
  16. J

    KICKDOWN CABLE ADJUSTMENT

    Hello all ,i,m looking for some help regarding how much travel should there be from idle to full throttle from crimp on cable, i have set cable with the sump off to make sure it is at the correct start point ,it is BW 35 box and i am running a holley carb, could anyone please measure what they...
  17. J

    Sorry would,nt let me write anymore, i have taken some pics i will try to send them to you, do...

    Sorry would,nt let me write anymore, i have taken some pics i will try to send them to you, do you know how much travel i should have on the cable, it only lifts up about 3/4 inch, John
  18. J

    Hello again Harvey hope you are well.i.m back out in the garage again, working on pop, i have...

    Hello again Harvey hope you are well.i.m back out in the garage again, working on pop, i have set the kickdown crimp with the sump off to get it right, the cam is at rest as it should be with just a little slack at linkage as you explained ast time we spoke,I only have about 3/4 inch of travel...
  19. J

    Rear band

    Ok thanks Harvey
  20. J

    Rear band

    Is the cam suppose to move as soon as the throttle starts to open or only on full throttle when you want kickdown please,
  21. J

    Rear band

    Ok harvey thanks
  22. J

    Rear band

    Any pictures you have would be usefull please.
  23. J

    Rear band

    Hello once again Harvey hope you have been well in these trying times, when you gave me advice about cam on kickdown valve should the cam travel all the way on acceleration please.
  24. J

    Rear band

    Thanks once again Harvey, will have a look at the weekend, no doubt i,ll get back to you LoL
  25. J

    Rear band

    Hello again Harvey, trying to get the correct adjustment on kickdown cable, i have had the sump off again, and i can see where the cable attacthes to the cam ,just wondered if you have any pictures of how this should sit against the valve please, John
Top